A collection of quick-grab tools built by a mixer, for mixers.

DELAY & REVERB CALCULATOR

Calculate tempo-synced delay times plus reverb pre-delay and decay values from BPM or tap tempo, with straight, dotted, and triplet note divisions.

4 taps to lock

REVERB TIMING

ABOUT THIS TOOL

Tap Tempo calculates BPM from the average interval across the four most recent taps, updating with each additional tap. Straight, dotted, and triplet modes provide the corresponding musical subdivisions for tempo-synced delay times.

The reverb section uses the same tempo grid to calculate pre-delay and decay times across five preset sizes, from the very official terms Tight to Lost in Space. These presets provide progressively longer timing references rather than simulations of physical room sizes. The values are starting points, not rules, and should be adjusted based on the source, arrangement, reverb algorithm, and desired sound.

Use the COPY control beside any millisecond value to paste the number directly into a delay or reverb plug-in.

Understanding Tempo-Synced Delay & Reverb

Delay and reverb are two of the most useful tools for creating depth and space in a mix. While they're often used for similar purposes, they approach that space differently. Delay creates distinct repetitions of a signal, while reverb produces a dense collection of reflections that we perceive as a continuous acoustic environment.

Timing either effect relative to the song's tempo can be a useful starting point, but as with most things in mixing, there's no hard-and-fast rule that says your effects need to be perfectly in time.

Sometimes the best setting is the one that doesn't immediately draw attention to itself.

Understanding Musical Subdivisions

The Delay & Reverb Calculator converts a song's tempo into milliseconds for common musical subdivisions, including straight, dotted, and triplet values.

At 120 BPM, for example, a quarter note lasts 500 ms, an eighth note lasts 250 ms, and a dotted eighth note lasts 375 ms.

Straight subdivisions follow the standard rhythmic divisions of a beat. Dotted values extend those durations by 50%, while triplet values divide the corresponding note duration into three equal parts across the space normally occupied by two.

These relationships are particularly useful for rhythmic delays. A quarter-note delay can reinforce the pulse of a song, while a dotted eighth can create movement that plays against the underlying beat.

But don't overlook the space between those calculated values. A delay that sits slightly ahead of or behind a strict subdivision can sometimes work better with the performance.

Using Delay in a Mix

Tempo-synced delays can add rhythmic interest without requiring additional notes or performances.

On vocals, a quarter- or eighth-note delay can fill the space between phrases while maintaining a sense of movement. Shorter delays can create thickness or width without being perceived as obvious repetitions.

Feedback and filtering are just as important as the delay time itself. A relatively loud repeat with significant high-frequency content will tend to draw more attention than a darker repeat sitting farther back in the mix.

It's also worth remembering that a delay doesn't necessarily need to be audible as a distinct effect to serve its purpose. Sometimes it's simply filling a little space around the source.

Reverb Pre-Delay

Pre-delay is the amount of time between the original signal and the onset of the reverb.

It's especially useful when you're trying to create space around a source without immediately washing out its initial transient.

On a vocal, for example, increasing pre-delay can allow the initial consonants and articulation to come through before the reverb begins to build. On drums, it can help preserve some of the attack while still providing a sense of room or ambience.

Tempo-based subdivisions provide a convenient reference for pre-delay, but there's no reason to assume that a mathematically synchronized setting will always sound better.

Even relatively small changes can alter the perceived distance and clarity of a source.

Reverb Decay Time

Reverb decay time, sometimes referred to as RT60, describes how long it takes for the reverberant sound level to decrease by 60 dB after the source stops.

Unlike delay time, decay doesn't necessarily need to correspond to a musical subdivision.

A longer decay can add size and sustain, but it can also build up between notes and obscure detail in a busy arrangement. A shorter decay may keep things cleaner, although it might not provide the sense of space you're looking for.

Tempo-derived decay values can be useful as starting points, particularly when you're trying to make the reverb settle before the next phrase or rhythmic event.

But decay is also affected by the reverb's frequency-dependent behavior, diffusion, density, and the way the effect interacts with the rest of the arrangement.

It's generally more useful to listen to how the reverb fills the space between notes than to worry about whether its decay corresponds to an exact rhythmic value.

Creating Depth Without Losing Clarity

One of the more useful things to consider when working with delay and reverb is how they affect the perceived distance of a source.

Pre-delay, early reflections, decay length, filtering, and wet/dry balance all contribute to that impression.

A longer pre-delay can help separate the source from its reverberant tail, while shorter pre-delay settings may make the source feel more closely connected to the room.

Filtering can also make a significant difference. Removing unnecessary low-frequency energy from a reverb return can prevent buildup, while reducing high frequencies can help the effect sit behind the dry signal.

Sometimes a carefully filtered delay can create a greater sense of space than adding more reverb.

Use the Numbers as a Starting Point

The goal of tempo-based calculations isn't to force every effect into a rhythmic grid. It's to give you a reliable reference that you can adjust from.

Start with a subdivision that makes sense for the arrangement, then listen to what the effect is actually contributing.

If the delay feels too obvious, try changing its level, filtering, or feedback before assuming the timing is wrong. If the reverb is clouding the mix, consider its pre-delay, frequency content, and decay rather than simply turning it down.

The calculator gives you the timing. What you do with that timing is what makes it musical.

← ALL CALCULATORS